| Perforce 2002.2 System Administrator's Guide | ||
|
<< Previous Chapter Tuning Perforce for Performance |
Table of Contents Index Perforce on the Web |
Next Chapter >> Perforce Proxy |
|
Note |
Unless otherwise specified, the material presented here applies equally to Windows NT, Windows 2000, and Windows XP. |
If you have Administrator privileges, it is usually best to install Perforce as a service. If you don't, install it as a server.
Under Windows 2000 or higher, you need Administrator privileges to install Perforce as a service, and Power User privileges to install Perforce as a server.
You are prompted to specify the location of the client executables, the port (P4PORT) on which the client should attempt to contact the Perforce server, the default editor, and the default username.
When specifying the port for the client to use, don't forget to include the hostname in the form hostname:port. See "Telling Perforce client programs which port to talk to" on page 13 for details on P4PORT.
If the installer detects older versions of Perforce client or server software on the machine, you are given the option to rename the old executables to prevent PATH-dependent conflicts.
You are prompted to specify the directory for the client and server executables, the port on the local machine where the Perforce server or service will listen to client requests (P4PORT), the default editor, and the default username.
The installer selects default locations for the P4LOG error log file and the journal file. If an earlier version of Perforce was installed on the machine, these locations are based on those already in use.
If you have Administrator privileges, the installer installs Perforce and configures it to run as an auto-starting service. The service is set up and started after the installation is complete, and automatically restarts whenever the machine is rebooted. If you do not have Administrator privileges, a shortcut to run Perforce as a server is placed into your Start menu.
If the installer detects older versions of Perforce client or server software on the machine, you are given the option to rename the old executables to prevent PATH-dependent conflicts.
As with the typical administrator install, you are prompted to specify the location of client and server executables, the port on the local machine where the Perforce server or service will listen to client requests, the default editor, and the default username.
Unlike the typical administrator install, you are allowed to optionally specify separate directories for the client and server executables, as well as server root, server port, and whether to set up Perforce as an auto-starting (or non-auto-starting) service or server process. The locations of any existing P4LOG file and journal file are displayed for reference, and may be changed later using p4 set.
If you try to install a Perforce service while another Perforce server is running, you will see the error message:
Setup has determined that a Perforce Server could be running. Please shut down all Perforce Servers before continuing the installation.
Failure to shut down the running Perforce server(s) will result in conflicts between the newly installed service and the existing server.
As with the other installation options, if the installer detects older versions of Perforce client or server software on the machine, you are given the option to rename the old executables to prevent PATH-dependent conflicts.
The uninstall procedure removes everything except your server data; the Perforce server, service, and client executables, registry keys, and service entries are all deleted. The database and depot files in your server root, however, are always preserved.
Throughout most of the documentation set, the terms "Perforce server" or "p4d" are used to refer to "the process at the back end that manages the database and responds to requests from Perforce clients". Under Windows, this can lead to ambiguity; the back-end process can run as either a service (p4s.exe, which runs as a thread) or as a server (p4d.exe, which runs as a regular process). From a Windows administrator's point of view, these are important distinctions. Consequently, the terminology used in this chapter uses the more precise definitions.
The Perforce service (p4s.exe) and the Perforce server (p4d.exe) executables are copies of each other; they are identical apart from their filenames. When run, they use the first three characters of the name with which they were invoked (that is, either p4s or p4d) to determine their behavior. For example, invoking copies named p4smyserver.exe or p4dmyservice.exe will invoke a service and a server, respectively.
If you are running at Release 99.2 or above, you can also use the command:
p4 admin stop
to stop the Perforce service.
You can also start the Perforce server manually from an MS-DOS window. The server executable, p4d.exe, is normally found in your P4ROOT directory. To start the server, first make sure your current P4ROOT, P4PORT, P4LOG, and P4JOURNAL settings are correct, then run:%P4ROOT%\p4d
If you want to start a server using settings different than those set by P4ROOT, P4PORT, P4LOG, or P4JOURNAL, you can use p4d command line flags. For example:
c:\test\p4d -r c:\test -p 1999 -L c:\test\log -J c:\test\journal
will start a Perforce server process with a root directory of c:\test, listening to port 1999, logging errors to c:\test\log, and with a journal file of c:\test\journal.
Note that p4d command line flags are case sensitive.
If you are running at Release 99.2 or above, use the following command:
p4 admin stop
to stop the Perforce server.
If you are installing your server root on a network drive, the Perforce installer (perforce.exe) requests a valid combination of userid and password at the time of installation. This user must have administrator privileges. (The service will also run as this user, rather than System)
While the Perforce NT service will run reliably using a network drive as the server root, there is still a marked performance penalty due to of increased network traffic and slower file access. For this reason, we recommend that the depot files and Perforce database be on a drive local to the machine on which the Perforce service is running.
You can, however, install additional services to start up additional Perforce servers (that is, running as Windows services) automatically.
If your intent is to set up multiple services to increase the number of users you support without purchasing more user licenses, you are violating the terms of your Perforce License Agreement.
Before you begin, you should read and understand "Windows configuration parameter precedence" on page 108. Once you understand the precedence of environment variables in determining Perforce configuration, you'll find setting up multiple Perforce services to be straightforward. To add a new service, you need to:
You wish to create a second Perforce service with a root in C:\p4root2 and a service name of
"Perforce2". You're running Release 99.1/10994 or greater, and the svcinst executable is
in the server root of his first Perforce NT service, which is in C:\perforce.
Verify that your p4d.exe executable is at Release 99.1/10994 or greater:
(We'll assume the revision level is correct; if not, you'd have to download a newer version
from http://www.perforce.com and upgrade the server before continuing.)
Create a P4ROOT directory for the new service:
Copy the server executables - both p4d.exe (the server) and p4s.exe (the service) - and
your license file into the new directory:
copy c:\perforce\p4d.exe c:\p4root2
copy c:\perforce\p4d.exe c:\p4root2\p4s.exe
copy c:\perforce\license c:\p4root2\license
Use svcinst.exe, (the service installer) to create the "Perforce2" service:
svcinst create -n Perforce2 -e c:\p4root2\p4s.exe -a
After the "Perforce2" service has been created, set the service parameters for the
"Perforce2" service:
p4 set -S Perforce2 P4ROOT=c:\p4root2
p4 set -S Perforce2 P4PORT=1667
p4 set -S Perforce2 P4LOG=log2
p4 set -S Perforce2 P4JOURNAL=journal2
Finally, use the service installer to start the "Perforce2" service:
The second service is now running, and both services will start automatically the next time
you reboot.
System environment variables can be set with:
While not all Perforce failures are caused by OS-level problems, a number of symptoms may indicate the OS is at fault. Examples include: the system crashing, the Perforce server exiting without any error in its log and without Windows indicating that the server crashed, or the Perforce NT service not starting properly.
Many of these problems may be resolved by installing Service Packs. A machine running NT 4.0 with Service Pack 6 and a plain VGA video driver is very stable.
In particular, Perforce support personnel have also found that many sites have been able to reduce or eliminate OS-level instability problems by re-installing NT Service Pack 6; consequently, we recommend that SP6 be installed on any NT system running the Perforce server or service.
In some cases, installing third-party software after installing a Service Pack can overwrite critical files installed by the service pack; reinstalling your most-recently installed service pack will often correct these problems. If you've installed another application after your last service pack, and server stability appears affected since the installation, consider reinstalling the service pack.
As a last resort, it may pay to install Perforce on another system to see if the same failures occur, or even to reinstall the OS and Perforce on the faulty system.
The reason for this is that Perforce clients sometimes use the DOS shell (cmd.exe) to start programs such as user-specified editors or diff utilities. Unfortunately, the DOS shell knows that when a Windows command is run (such as a GUI-based editor like notepad.exe), it doesn't have to wait for the command to complete before terminating. When this happens, the Perforce client then mistakenly believes that the command has finished, and attempts to continue processing, often deleting the temporary files that the editor or diff utility had been using, leading to errors about temporary files not being found, or other strange behavior.
You can get around this problem in two ways:
| Perforce 2002.2 System Administrator's Guide | ||
|
<< Previous Chapter Tuning Perforce for Performance |
Table of Contents Index Perforce on the Web |
Next Chapter >> Perforce Proxy |